The ultrasonic aluminum cover cleaning machine can carry out ultrasonic cleaning, silicification, pre drying, drying and sterilization of rubber plug or aluminum cover in a closed box at one time. The advanced programmable controller (PLC) is adopted as the main controller, and the electronic touch screen is used for operation. The whole process is displayed in Chinese characters, which is easy to operate.

各种工艺参数如清洗时间、漂洗时间、干燥时间、干燥温度可事先预置，只需按下“运行”键，整个过程可自动完成。除自动方式外还设有“半自动”和“手动”方式可供选择。

Various process parameters such as cleaning time, rinsing time, drying time and drying temperature can be preset in advance. Just press the "run" key, and the whole process can be completed automatically. In addition to the automatic mode, there are also "semi-automatic" and "manual" modes to choose from.

设备的使用方法以及操作时应注意以下几点：

The following points should be paid attention to when using and operating the equipment:

（1）生产操作，操作人员应用水配合排刷，将罐体内所有部位清理干净，然后

(1) During production operation, the operator shall clean all parts of the tank with water and brush, and then

带上橡胶手套，用丝毛巾和无盐水，分别将罐体内各个部位清理干净。

Wear rubber gloves and clean all parts of the tank body with silk towel and no salt water.

（2）由化验人员检查无盐水澄明度，合格后方可注如罐内，水质标准毛点

(2) The laboratory personnel shall check that there is no clarity of brine, and it can be injected into the tank only after it is qualified. The water quality standard is the gross point

不多于2个/100ml点。

No more than 2 / 100ml points.

（3）倒入过筛胶约10万只，打开无盐水进水阀，水位高度应溢流孔流出为

(3) Pour about 100000 sieving glue, open the brine free water inlet valve, and the water level shall be at the overflow hole

（4）此时可实行超声波清洗，调节压缩空气搅拌，使胶塞在罐内均匀翻为宜。调节无盐水流量，产生溢流洗涤。溢流同时可稍打开底部排污阀放水。

(4) At this time, ultrasonic cleaning can be carried out, and compressed air mixing can be adjusted to turn the rubber plug evenly in the tank. Adjust the flow of no brine to produce overflow washing. At the same time of overflow, slightly open the bottom blowdown valve to drain water.

（5）开启控制开关，接通JCX—5KW超声波清洗机电源开关，延时约15

(5) Turn on the control switch and turn on the power switch of jcx-5kw ultrasonic cleaning machine, with a delay of about 15 minutes

秒中后，即刻听到继电器的闭合声，机器与洗涤可正常工作（具体情况可参阅

After seconds, the closing sound of the relay is heard immediately, and the machine and washing can work normally (see for details)

DY—5KW超声波清洗使用说明书）。

Dy-5kw ultrasonic cleaning operation manual).

（6）在洗胶塞时，胶塞表面粗糙不齐，易掉胶宵难于洗涤时，可减少洗涤量或

(6) When washing the rubber plug, the surface of the rubber plug is rough and uneven, which is easy to fall off. When it is difficult to wash at night, the washing amount can be reduced or

减少空气搅拌，以降低胶塞在洗涤过程中的互相磨擦，降低胶质间颗粒的脱落。

Reduce air stirring to reduce the mutual friction of rubber plugs in the washing process and reduce the falling off of colloidal particles.

（7）洗涤1.5小时后，由质检员检验，待检验合格后，关掉超声波主机电源，切断控制开关，停水、停气，放尽罐内洗涤水，然后打开罐内下部的出料口，出料即可。

(7) After washing for 1.5 hours, it shall be inspected by the quality inspector. After passing the inspection, first turn off the power supply of the ultrasonic host, cut off the control switch, stop water and gas, drain the washing water in the tank, and then open the discharge outlet at the lower part of the tank to discharge the material.

以上就是今天小编给大家提供的精彩内容，更多的精彩内容请点击进入我们的网站：全自动超声波清洗机http://senfuai.com

The above is the wonderful content provided by Xiaobian today. For more wonderful content, please click to enter our official website: automatic ultrasonic cleaning machine http://senfuai.com