启航彩电镀中，预处理的用意为了往除工件表面存有污物及杂质，使之成为适宜电镀的活性表面。电镀品质不良原由较多是预处理欠好。而预处理欠好，大多未应用超音波清洗设备。

启航彩In electroplating, the purpose of pre-treatment is to remove dirt and impurities from the surface of the workpiece, making it an active surface suitable for electroplating. There are many reasons for poor electroplating quality, which are due to poor pre-treatment. However, the preprocessing is not good enough, and most of them have not applied ultrasonic cleaning equipment.

启航彩电镀前处理时会必要依据工件的具体情况，选用适合的方法进行合理清洗。金属基材一般分为冲压件和压铸件。冲压件上边的油渍为一般冲压油，因其密度非常高所以比较随便清洗。一般可用酸洗、电解等。而锌、铝、铜等压铸件属较难清洗的因压铸件中添加了各种元素，此外在成形、拉涨、压延、切削、抛光的过程中还有必要运用各种油品，如机油、抛光油等。

During the pre-treatment of electroplating, it is necessary to select suitable methods for reasonable cleaning based on the specific situation of the workpiece. Metal substrates are generally divided into stamped parts and die castings. The oil stains on the top of the stamped parts are ordinary stamping oil, which is relatively easy to clean due to its high density. Generally, acid washing, electrolysis, etc. can be used. Zinc, aluminum, copper and other die castings are difficult to clean due to the addition of various elements in the die castings. In addition, it is necessary to use various oil products such as engine oil and polishing oil in the processes of forming, stretching, rolling, cutting, and polishing.

有关超声波清洗机而言，机油能够轻松往除。但抛光油分成黄油白油、绿油等，这比较难以往除。因此，有必要选择适合的超声清洗设备及清洗液。

Regarding ultrasonic cleaning machines, oil can be easily removed. But the polishing oil is divided into butter, white oil, green oil, etc., which is difficult to remove. Therefore, it is necessary to choose suitable ultrasonic cleaning equipment and cleaning solution.

超声频率一般为20-100KHZ之间。一般工件的预处理，一般采用低频、中功率的超声清洗设备，如频率25-28KHZ，功率1W/cm。由于低频比高频在介质中随便发生空蚀，有关外形简易、并不十分细致的工件，超声波清洗机能符合要求。特征是噪声较大价格便宜。对一些细致度较高的工件，现使用的一般均为高频40-68KHZ大功率的超声清洗机。因此类清洗机关于间隙、间隙、深孔、埋孔等表面形繁杂的工件清洗效果较好。可是超声清洗的效果只是有溶液到达的地方才能起到清洗效果。也是说要避免深孔、埋孔含有气体，而且要留意杂质下落、油渍上漂和处理清洗不到位的状况。

启航彩The ultrasound frequency is generally between 20-100KHZ. The pre-treatment of general workpieces generally uses low-frequency and medium power ultrasonic cleaning equipment, such as 25-28KHZ frequency and 1W/cm power. Due to the random occurrence of cavitation in the medium at low frequencies compared to high frequencies, ultrasonic cleaning can meet the requirements for workpieces with simple and not very detailed shapes. The characteristic is high noise and low price. For some workpieces with high precision, the commonly used ones are high-frequency 40-68KHZ high-power ultrasonic cleaning machines. Therefore, this type of cleaning machine has a better cleaning effect on workpieces with complex surface shapes such as gaps, gaps, deep holes, and buried holes. But the effect of ultrasonic cleaning can only be achieved where the solution reaches. It also means to avoid deep holes and buried holes containing gas, and to pay attention to the situation of impurities falling, oil stains floating, and inadequate treatment and cleaning.