你知道单工位旋转喷淋清洗机使用的空化作用具体是怎样实现的吗？实际上这个作用广泛应用于多个类型的清洗机中，下面小编就来为您讲讲。

Do you know how the cavitation effect used by the single station rotary spray washer is realized? In fact, this function is widely used in many types of cleaning machines. The following section will tell you about it.

单工位旋转喷淋清洗机的空化作用就是超声波以每秒两万次以上的压缩力和减压力交互性的高频变换方式向液体进行透射。在减压力作用时，液体中产生真空核群泡的现象，在压缩力作用时，真空核群泡受压力压碎时产生强大的冲击力，由此剥离被清洗物表面的污垢，从而达到精密洗净目的。

The cavitation effect of the single station rotary spray washer is that the ultrasonic wave transmits to the liquid in the high-frequency transformation mode of the interaction of the compression force and pressure reduction more than 20,000 times per second. In the process of pressure reduction, the phenomenon of vacuum core bubble cluster is generated in the liquid. In the process of compression, the vacuum core bubble cluster is crushed under pressure, which generates a strong impact force, thus stripping the dirt on the surface of the object to be cleaned, so as to achieve the purpose of precise cleaning.

单工位旋转喷淋清洗机在液体中会沿着声的传播方向产生流动的现象被称为直进流，其声波强度在0.5W/cm2时，肉眼能看到直进流，垂直于振动面产生流动，流速约为10cm/s。通过此直进流使被清洗物表面的微油污垢被搅拌，污垢表面的清洗液也产生对流，溶解污物的溶解液与新液混合，使溶解速度加快，对污物的搬运起着很大的作用。

The phenomenon that the single station rotary spray washer will flow in the liquid along the sound propagation direction is called direct inflow. When the sound intensity is 0.5W/cm2, the direct inflow can be seen with the naked eye, and flow is generated perpendicular to the vibration surface, with a flow rate of about 10cm/s. Through this direct inflow, the tiny oil dirt on the surface of the object to be cleaned is stirred, and the cleaning solution on the surface of the dirt also has convection. The solution to dissolve the dirt is mixed with the new solution, which speeds up the dissolution rate and plays a great role in the transportation of the dirt.

单工位旋转喷淋清洗机的液体粒子推动就会产生的加速度，在运行时对于频率较高的设备，其空化作用就是很不显著了，这时候的清洗主要靠液体粒子超声作用下的加速度撞击粒子对污物进行超精密清洗。

The acceleration generated when the liquid particles of the single station rotary spray washer are pushed, the cavitation effect of the equipment with high frequency is not significant during operation. At this time, the cleaning mainly depends on the acceleration of the liquid particles under the ultrasonic action to impact the particles for ultra precision cleaning.

此外单工位旋转喷淋清洗机的安装说明书连接清洗机的电控柜和主机间的温控传感器信号、超声驱动线、加热器控制线等线路，并接通380VAC电源，安装清洗机的上水管、放水管与溢流排放管。

In addition, the installation instructions of the single station rotary spray washer connect the electric control cabinet of the washer and the temperature control sensor signal, ultrasonic drive line, heater control line and other lines between the main machine, connect the 380VAC power supply, and install the water supply pipe, drain pipe and overflow drain pipe of the washer.

单工位旋转喷淋清洗机需要有效的向清洗池内加入其适量清水，其液面高度主要是以浸没将要清洗的零部件为准，一般不超过清洗池的四分之三。启动电控加热开关，将水温调节旋钮上的白色刻度线指向适当的温度（应为60℃左右）。

The single station rotary spray washer needs to effectively add an appropriate amount of clean water into the cleaning pool. The liquid level height is mainly based on the immersion of the parts to be cleaned, generally not more than three quarters of the cleaning pool. Start the electric control heating switch and point the white scale mark on the water temperature regulating knob to the appropriate temperature (about 60 ℃).

清洗机在使用过程中，清洗剂的温度不应超过70℃。待水温升至40℃左右时，将UC-O3零部件清洗剂加入清洗池中（一般一次5kg左右），徐徐搅动清水使其充分溶解（此时亦可启动越声波或开启鼓气装置进行搅拌）。

During the use of the cleaning machine, the temperature of the cleaning agent should not exceed 70 ℃. When the water temperature rises to about 40 ℃, add the UC-O3 parts cleaning agent into the cleaning pool (generally about 5kg at a time), and slowly stir the clean water to fully dissolve it (at this time, you can also start the ultrasonic wave or open the air blowing device to stir).

单工位旋转喷淋清洗机使用的空化作用以及其安装事项就讲解到这里了，您对此有什么疑惑或者需求就来我们网站senfuai.com咨询了解吧！

The cavitation effect of single station rotary spray washer and its installation matters will be explained here. If you have any doubts or needs, please come to our website senfuai.com for consultation!