作为公认的环保、无污染环保设备，CNC高压清洗机可谓是“美名在外”，不需要更多地夸赞与好处的描述了，所以今天小编不说优势，只说CNC高压清洗机如何规范使用与日常维护。

As a recognized environmental protection and pollution-free environmental protection equipment, CNC high-pressure cleaning machine is "famous" and does not need to be praised and described more. Therefore, today's Xiaobian does not talk about advantages, but only how to standardize the use and daily maintenance of CNC high-pressure cleaning machine.

操作说明

Operating instructions

将CNC高压清洗机放置在一个通风、干燥、无水且无阳光直射暴晒的场所，加以固定。

Place the CNC high-pressure washer in a ventilated, dry, anhydrous place without direct sunlight for fixation.

1、将调压轮旋松，插上电源插头。

1. Unscrew the pressure regulating wheel and plug in the power plug.

2、打开喷枪，开动开关按钮（不同清洗机开关按钮颜色不同，这里不作说明），按下引水阀杆排除进水管及泵内空气。

2. Open the spray gun, start the switch button (the color of the switch button of different washers is different, which is not explained here), press the water diversion valve stem to exhaust the air in the water inlet pipe and pump.

3、待喷枪出水后，放开旋动调压轮，调节输出压力至合适程度即可。如果电压偏低应降低输出压力，以减轻电动机负荷，如电压低于或高于清洗机所能承受的负荷与范围，需要立刻停止使用，避免烧毁电动机。

3. After the spray gun discharges water, release and rotate the pressure regulating wheel to adjust the output pressure to an appropriate level. If the voltage is low, the output pressure should be reduced to reduce the load of the motor. If the voltage is lower or higher than the load and range that the washer can bear, it is necessary to stop using it immediately to avoid burning the motor.

保养维护方法

Maintenance method

定期检查电源插头、电源线、漏电保护装置，如有损坏，应该立即停止使用，联系的人士进行维修处理。

Regularly check the power plug, power cord and leakage protection device. In case of damage, stop using immediately and contact professional personnel for maintenance.

定期检查接地装置，保证良好接地。

Check the grounding device regularly to ensure good grounding.

电动机、控制装置如进水、受潮，严禁使用并立即维修。

If the motor and control device are affected by water or moisture, it is forbidden to use them and repair them immediately.

定期检查润滑油，应保持在油位刻线上，润滑油每动转200小时更换一次。如有其它液体进入曲轴箱内应及时换油。

Check the lubricating oil regularly and keep it on the oil level mark. Replace the lubricating oil every 200 hours. If any other liquid enters the crankcase, the oil shall be changed in time.

检查三角皮带松紧程度，如不合格应及时调整。

Check the tightness of the V-belt and adjust it in time if it is unqualified.

定期检查各连接、紧固部位螺钉有无松动，如有松动应立即拧紧。

Regularly check whether the screws of all connecting and fastening parts are loose. If they are loose, tighten them immediately.

定期清洗水池、清除滤网上的杂质。

Regularly clean the water tank and remove impurities on the filter screen.

这里注意:维修保养时请切除电源、密封圈装配前应涂抹黄油再装上。

Note here: during maintenance, please cut off the power supply. Before assembly, the sealing ring should be coated with grease and then installed.

CNC高压清洗机如何规范使用与日常维护的相关内容便是如此了，您对此有什么不明白的方面，欢迎来我们网站senfuai.com进行咨询了解！

This is how to standardize the use and daily maintenance of CNC high-pressure cleaning machines. If you don't understand anything about this, please come to our website senfuai.com for consultation!