众做周知，清洗机的使用寿命长短与日常维护有很多的联系，维护好了它的工作效率才能持续，而且使用的时间也会越来越长，下面我们来看下相关内容吧。

As we all know, the service life of the cleaning machine has a lot to do with daily maintenance. Only by maintaining its work efficiency can it continue to be efficient, and the use time will be longer and longer. Let's take a look at the related content.

工作效率比较高，相对于人工清洁来说，它可以快速的除尘除垢，还可以节省人工的劳动力。即使不用专用的清洗剂，它在清洁的时候加入适当的洗涤剂也是可以达到很好的清洁效果。而且它的精度高，能够清洁到很细微的缝隙和孔洞中，能满足的特殊要求。

The work efficiency is relatively high. Compared with manual cleaning, it can quickly remove dust and dirt, and also save manual labor. Even without special detergent, it can achieve good cleaning effect by adding appropriate detergent when cleaning. Moreover, it has high precision and can be cleaned into very fine cracks and holes, which can meet the special requirements of professionals.

对于被清洗的物件不管是大的小的，简单的还是复杂的，单量的还是批量的，清洗机都是可以获得比较的清洁度。更重要的是通过清洗机清洗，更加节约水，噪音也比较小，而且设备的使用寿命很长，操作也比较简单。

For the cleaned objects, whether large or small, simple or complex, single quantity or batch, the cleaning machine can obtain a relatively clean degree. What's more, cleaning with a cleaning machine saves more water, makes less noise, and has a long service life and simple operation.

通过日常的检查，及时发现问题可以为设备的正常运转打好“预防针”。一般日常维护有6项检查：

Through daily inspection, finding problems in time can provide a "preventive injection" for the normal operation of the equipment. There are 6 inspections for general routine maintenance:

1、检查清洗机的环境温度和湿度是否符合标准。

1. Check whether the ambient temperature and humidity of the cleaning machine meet the standards.

2、检查数显温控仪、电流表显示的读数是否正确。

2. Check whether the readings displayed by digital temperature controller and ammeter are correct.

3、检查二极管和指示灯是否正常工作。

3. Check the diodes and indicators for proper operation.

4、检查清洗机的管路出水口出水量情况。

4. Check the water output of the pipeline outlet of the washing machine.

5、检查清洗机工作时振动、噪音是否异常。

5. Check whether the vibration and noise of the cleaning machine are abnormal during operation.

6、检查超声波清洗设备的表面是否有灰尘。

6. Check whether there is dust on the surface of ultrasonic cleaning equipment.

注意，清洗机在使用中也有可能发生常见问题。例如，在超声波振子暴露在湿气中的情况下，可以用兆欧表检查与换能器连接的插头，通过检查绝缘电阻值可以判断基本的状况，一般要求绝缘电阻在5兆欧表以上。如果达不到该绝缘电阻值，通常换能器是湿的，所以可以将换能器整体放入烤箱，设定在温度100度左右，干燥3小时，或者使用电吹风去气直到电阻值正常。

Note that common problems may also occur in the use of the cleaning machine. For example, when the ultrasonic vibrator is exposed to moisture, the plug connected to the transducer can be checked with a megger, and the basic condition can be judged by checking the insulation resistance value. Generally, the insulation resistance is required to be more than 5 megger. If the insulation resistance value cannot be reached, the transducer is usually wet, so you can put the transducer into the oven as a whole, set the temperature at about 100 ℃, and dry it for 3 hours, or use an electric hair dryer to remove the moisture until the resistance value is normal.

严禁在无清洗液的情况下接通电源，即清洗缸内未进入一定量的清洗液，不得关闭超声波开关；有加热设备的清洗设备在没有液体时请勿打开加热开关。更多注意事项就来关注网站senfuai.com看信息吧。

It is strictly forbidden to turn on the power supply without cleaning fluid, that is, do not turn off the ultrasonic switch without a certain amount of cleaning fluid in the cleaning cylinder; Do not turn on the heating switch when there is no liquid in the cleaning equipment with heating equipment. For more notes, follow the website www.jnthcsb Read the information. Com.