1. The higher the output power, the better the cleaning effect. However, the correct and reasonable selection of ultrasonic output hydraulic parts. The ultrasonic cleaning effect of ultrasonic cleaning machine is directly proportional to (output x cleaning time). When the output power is low, it takes a certain time to remove dirt. When the power reaches this value, the dirt can be removed immediately. If the power is too large, the cavitation intensity will be greatly improved and the cleaning effect will be improved. However, corrosion spots will appear even on more precise parts, so the loss is not worth it. In addition, the vibration plate at the bottom of the cleaning tank of the hydraulic parts ultrasonic cleaning machine has serious cavitation, which increases the water spot corrosion. The use of organic solvents, such as trichloroethylene, is basically good. When the surface of the vibrating plate is damaged, the more serious the cavitation corrosion is, the greater the stress is. Therefore, it is necessary to select the ultrasonic output according to the actual application.

2.液压件超声清洗机的输出功率、空化阈值和频率的选择与输出功率的选择密切相关。频率越高，空化阈值越高。换言之，频率越低，空化现象越容易发生。在低频条件下，液体压缩变稀的时间间隔越长。

2. The selection of output power, cavitation threshold and frequency of hydraulic parts ultrasonic cleaning machine is closely related to the selection of output power. The higher the frequency, the higher the cavitation threshold. In other words, the lower the frequency, the more likely cavitation is to occur. Under low frequency conditions, the longer the time interval between liquid compression and thinning.

在气泡破裂之前，空腔的强度随着气泡体积的增大而增大。它有助于清洁。频率约为40KHz，声强相同，产生的空化气泡多于20kHz，穿透力强。适用于表面形状复杂的工件和挡块的清洗。空化噪声小，但空气的化学强度低。适用于清洗脏污和粘结强度弱的清洗零件

Before the bubble burst, the strength of the cavity increases with the increase of the bubble volume. It helps to clean. The frequency is about 40KHz, the sound intensity is the same, the cavitation bubbles generated are more than 20kHz, and the penetration is strong. It is suitable for cleaning workpieces and stops with complex surface shape. The cavitation noise is small, but the chemical intensity of the air is low. It is suitable for cleaning dirty and weak bonding parts

3.液压件超声波清洗机的功率输出公式为

3. The power output formula of ultrasonic cleaning machine for hydraulic parts is

（1），由换能器（俗称振动头）计算得出。目前市场上有两种逆变器输出：50W1pcs和60WPCs。液压件超声波清洗机功率：换能器个数n× 50W或n× 知道水槽的长度和宽度就足够了。振动器与振动器之间的距离为100毫米

(1) , calculated by transducer (commonly known as vibrating head). At present, there are two inverter outputs on the market: 50w1pcs and 60wpcs. Power of ultrasonic cleaning machine for hydraulic parts: number of transducers n ×  50W or n ×  It's enough to know the length and width of the sink. The distance between vibrators is 100mm

（3）振动器的输出功率通常为50瓦或60瓦。储罐通常放置在600 x 400 mm表面的底部。通常，24个振动器是均匀分布的。如果污染严重，可以适当提高产量，使之均匀。28岁时，总功率约1400W，发电机功率1500W

(3) The output power of the vibrator is usually 50 watts or 60 watts. Tanks are usually placed at the bottom of a 600 x 400 mm surface. Generally, 24 vibrators are evenly distributed. If the pollution is serious, the output can be appropriately increased to make it uniform. At the age of 28, the total power is about 1400W and the generator power is 1500W

（4）振动器停机时，液压件超声波清洗机的输出功率为60x40x0和55x1320w

(4) When the vibrator is stopped, the output power of the ultrasonic cleaning machine for hydraulic parts is 60x40x0 and 55x1320w

超声空化阈值与频率密切相关。频率越高，空化阈值越高。频率越低，空化阈值越低，空化越容易发生。教你选择液压零件超声波清洗机的功率。看完后就会知道，当工件表面较大或有污垢或工作表面附着力较高时，通常采用低频超声波清洗。高频超声波适用于某些精密零件的清洗。考虑到超声波清洗的效果和经济性，频率一般为20-130khz。

Ultrasonic cavitation threshold is closely related to frequency. The higher the frequency, the higher the cavitation threshold. The lower the frequency is, the lower the cavitation threshold is, and the more likely cavitation is to occur. Teach you to choose the power of ultrasonic cleaning machine for hydraulic parts. After reading it, you will know that when the workpiece surface is large or there is dirt or the working surface adhesion is high, low-frequency ultrasonic cleaning is usually used. High frequency ultrasonic wave is suitable for cleaning some precision parts. Considering the effect and economy of ultrasonic cleaning, the frequency is generally 20-130khz.