启航彩从目前超声波业界的情况看，超音波重要分为自激式和它激式开关电源;超音波开关电源的运用关键是要根据超声波超声波换能器功率的规格、頻率的高低、容积去匹配就可以。功率较小的可以运用自激式，功率非常大的建议运用它激式。

From the current situation of the ultrasonic industry, ultrasonic is mainly divided into self-excited and other excited switching power supply; the key to the application of ultrasonic switching power supply is to match according to the power specification, frequency and volume of ultrasonic transducer. Small power can use self-excited type, power is very large, it is recommended to use other excited type.

启航彩超声波清洗机的开关电源又称超音波开关电源，它的作用是把大家的工作电压(230V或380V，60或65HZ)转换成超声波超声波换能器相一致的高频交流与沟通电子信号。

The switching power supply of ultrasonic cleaning machine is also called ultrasonic switching power supply. Its function is to convert everyone's working voltage (230V or 380V, 60 or 65Hz) into high-frequency AC and communication electronic signal consistent with ultrasonic transducer.

启航彩从运算放大器方法，可以采用线型运算放大器和开关电源电源电路，输出功率超音波开关电源从转换效率高方面充分考虑一般采用环形变压器的电路方法。线形可调稳压电源也是它特有的应用范围，它的优点是可以不严格要求电路匹配，允许功率不断快速变化。

启航彩From the operational amplifier method, linear operational amplifier and switching power supply circuit can be used. The output power of ultrasonic switching power supply takes full account of the circuit method of ring transformer from the aspect of high conversion efficiency. Linear adjustable power supply is also its unique application range, its advantage is that it can not strictly require circuit matching, allowing power to change rapidly.

启航彩超声波清洗机的使用说明书：

启航彩Operation manual of ultrasonic cleaning machine:

1、超声波清洗机的运用开关电源(230V)用三芯电源插头(火线零线、接地线、电线接头)。

1. The use of ultrasonic cleaning machine switching power supply (230V) with three core power plug (live wire, zero line, ground wire, wire connector).

启航彩2、清除干燥槽必不可少加上清洁液或水。清洁液或水的液位仪不能低于清除槽高度的三分之一。清除时，请根据不一样的清除要求，再加洗洁剂剂，提高清除效率高，所有洗洁剂剂必不可少符合不腐蚀清洗设备轴杆、机体的要求。

2. Remove the drying tank and add cleaning solution or water. The level gauge of cleaning liquid or water shall not be lower than one third of the height of cleaning tank. When cleaning, please add cleaning agent according to different cleaning requirements to improve the cleaning efficiency. All cleaning agents are essential and meet the requirements of non corrosive cleaning equipment shaft and body.

3、将被清除化合物放入金属材料框中，根据清除物的积垢水准，设定清除時间，一般3-12分鐘，十分难清除的化合物，可适当提升清除時间。(严禁把被清除化合物马上放进清除槽底运用)。

3. Put the removed compounds into the metal material frame, and set the removal time according to the scale level of the removed compounds, generally 3-12 minutes. For the compounds that are very difficult to remove, the removal time can be appropriately increased. (it is strictly forbidden to put the removed compounds into the bottom of the cleaning tank immediately).

4、将超声波清洗机的插头电源线加上230V的三芯电源线插头，开启电源开关设定好超声波工作时间，按“启动/停止”键一开始工作上，这时候液位仪呈现蛛网状波动，且随着振响，表述清洗设备已进入工作责任心。

4. Add the 230V three core power cord plug to the plug power cord of the ultrasonic cleaning machine, turn on the power switch, set the ultrasonic working time, and press the "start / stop" button to start working. At this time, the liquid level meter shows a spider wave, and with the vibration, the cleaning equipment has entered the sense of responsibility.

启航彩5、侧重的物件应依据挂具悬挂系统在清洁液中。

启航彩5. Focus on the object should be based on the hanger suspension system in the cleaning fluid.