多槽手动超声波清洗机应用于工业领域和清洗行业，且使用效果非常的好，在市场中很受欢迎，当然使用期间难免会遇到一些问题，下面就来讲几个常见的，以便您多预防。

The multi slot manual ultrasonic cleaning machine is applied in the industrial field and cleaning industry, and the use effect is very good. It is very popular in the market. Of course, it is inevitable to encounter some problems during use. Here are some common ones for you to prevent more.

1、多槽手动超声波清洗机打开电源开关，指示灯不亮。这种情况维修时须检查电源开关是否完好，漏电开关是否合上。如果开关完好再检查保险丝是否过载熔断，基本上可以解决。

1. Turn on the power switch of the multi tank manual ultrasonic cleaning machine, and the indicator light does not light up. In this case, check whether the power switch is in good condition and whether the leakage switch is closed. If the switch is intact, check whether the fuse is overloaded and blown, which can be basically solved.

2、多槽手动超声波清洗机打开电源开关后，指示灯亮，但没有超声波输出。这种情况比较复杂，维修时首先检查换能器与超声波功率板的连接插头是否有松脱，然后检查保险丝是否熔断。

2. After turning on the power switch of the multi tank manual ultrasonic cleaning machine, the indicator light is on, but there is no ultrasonic output. This situation is complicated. During maintenance, first check whether the connecting plug between the transducer and the ultrasonic power board is loose, and then check whether the fuse is blown.

如果一切正常有可能是超声功率发生器内部故障，用万用表打电源线明线，火线是否都通。在排除了发生器故障后再检查超声波换能器是否烧坏，是否需要更换。

If everything is normal, it may be the internal fault of the ultrasonic power generator. Use a multimeter to open the power line and check whether all the live wires are connected. After troubleshooting the generator, check whether the ultrasonic transducer is burnt out and needs to be replaced.

3、多槽手动超声波清洗机直流保险丝熔断。可能是整流桥堆或功率管烧毁，也可能是换能器老化，电流不稳，这些都可能造成电源发生器故障。维修时要多加注意。

3. The DC fuse of the multi slot manual ultrasonic cleaner is blown. It may be that the rectifier bridge stack or the power tube is burnt, or the transducer is aged and the current is unstable, which may cause the power generator failure. Pay more attention to maintenance.

注意：

be careful:

使用多槽超声波清洗机清洗工件时，需要注意槽液不能装得太满，以免出现两槽超声波清洗剂相互混合，清洗篮底部粘液被排出的现象。此外，清洗机的每个槽都应该是独立的操作过程，因此注意不要将两个槽的清洗剂串联使用，也不要人为减少操作过程和清洗操作时间。

When using the multi tank ultrasonic cleaning machine to clean the workpiece, it should be noted that the tank liquid cannot be filled too full, so as to avoid the phenomenon that the two tanks of ultrasonic cleaning agents are mixed with each other and the mucus at the bottom of the cleaning basket is discharged. In addition, each tank of the cleaning machine should be an independent operation process, so pay attention not to use the cleaning agents of the two tanks in series, nor artificially reduce the operation process and cleaning operation time.

多槽手动超声波清洗机常见三种问题以及有关注意事项就讲解到这里了，您多预防问题才是根本，更多信息获取就来我们网站senfuai.com咨询吧！

Here are the three common problems and relevant precautions of multi tank manual ultrasonic cleaning machine. How to prevent problems is the root. For more information, please come to our website senfuai.com!