超声波清洗是一种非常的清洗方法，特别适合当今高度发达的社会，可以用于各个领域。但是超声波清洗机本身非常准确，安装过程必须按照规格进行，耐心完成所有必要的工作，确保设备达到预期的效果。特别是超声波清洗机的安装预防措施包括以下几个方面。

Ultrasonic cleaning is a very advanced cleaning method, especially suitable for today's highly developed society, can be used in various fields. But the ultrasonic cleaning machine itself is very accurate, the installation process must be carried out according to the specifications, patiently complete all the necessary work, to ensure that the equipment achieves the desired effect. In particular, the installation precautions of ultrasonic cleaning machine include the following aspects.

一，是准备工作和喷砂处理。

1、 The emphasis is on Preparation and sandblasting.

在正式安装超声波清洗机之前，必须准备一种与超声波交换器(包括正确的)粘合的粘合剂。同时，超声波清洗机制造商必须停止超声波转换器和所需胶水的圆筒，停止喷砂。(威廉莎士比亚、超声波清洗机、超声波清洗机、超声波清洗机、超声波清洗机)喷砂接头必须符合要求，喷砂要求为钻石砂。对沙子的要求比较高。要慎重选择，要打孔等。喷洒沙子时压缩空气的压力必须调整以符合规定的要求，由空气源处理器的高压空气。

Before the installation of the ultrasonic cleaning machine, an adhesive must be prepared to adhere to the ultrasonic exchanger (including the correct one). At the same time, the ultrasonic cleaning machine manufacturer must stop the ultrasonic converter and the required glue cylinder, stop sandblasting. (William Shakespeare, ultrasonic cleaning machine, ultrasonic cleaning machine, ultrasonic cleaning machine, ultrasonic cleaning machine) the sandblasting joint must meet the requirements, and the sandblasting requirement is diamond sand. The demand for sand is relatively high. We should choose carefully and punch holes. When spraying sand, the pressure of compressed air must be adjusted to meet the specified requirements, and the high-pressure air dehumidified by the air source processor.

二，注意相关清洁工作。

2、 Pay attention to relevant cleaning work.

据超声波清洗设备制造商透露，蛇毒和超声波交换器需要停止清洗，后者需要应用准备好的溶液进行清洗，去除基本表面的一些污垢，然后进行清洗工作。(威廉莎士比亚、超声波、超声波、超声波、超声波、超声波、超声波、超声波)同时，超声波清洗机的汽缸需要连续清洗多次。干燥后接受特殊溶液，停一下。网眼垫的厚度应满足要求，不锈钢网要清洁干净。

启航彩According to the manufacturer of ultrasonic cleaning equipment, the snake venom and ultrasonic exchanger need to stop cleaning first, and the latter needs to use the prepared solution to clean, remove some dirt on the most basic surface, and then carry out the cleaning work. (William Shakespeare, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic, ultrasonic) at the same time, the cylinder of the ultrasonic cleaning machine needs to be cleaned continuously for many times. After drying, accept the special solution and stop. The thickness of mesh pad should meet the requirements, and the stainless steel mesh should be clean.

三，注意干燥、预热处理。

3、 Pay attention to drying and preheating.

清洁的超声波转换器、气瓶和网垫必须放入烤箱以停止干燥。干燥温度也要控制在该范围内。然后在干燥2小时后冷却到一定温度时要停止。超声波清洗机公司介绍说，完成所有粘合剂准备任务后，注意粘合剂(常温)，停止继续粘合剂。

Clean ultrasonic transducers, cylinders and mesh mats must be placed in the oven to stop drying. The drying temperature should also be controlled in this range. Then, after drying for 2 hours and cooling to a certain temperature, it should be stopped. Ultrasonic cleaning machine company said that after completing all the adhesive preparation tasks, pay attention to the adhesive (room temperature), stop adhesive.