目前，市场上的许多超声波振荡器都使用大型水质净化设备和超声波清洗机。它可以用超声波中的止溶液搅拌，清洁和消毒所需物品。超声波清洗机中的超声波振荡器需要注意哪些问题？

At present, many ultrasonic oscillators on the market use large water purification equipment and ultrasonic cleaning machines. It can be used to stir, clean and disinfect the articles needed by the ultrasonic solution. What problems should be paid attention to in the ultrasonic oscillator of the ultrasonic cleaner?

一注意液位标准（低于标准勿开机）

I. Pay attention to the liquid level standard (do not start the machine if it is lower than the standard)

由于超声波振荡器的清洗槽容量不同，所以对于液位的要求也有一定的差别，在使用超声波振荡器前要认真阅读说明书，详细了解低槽深、液位深度，在液位未达标的情况下或者无液情况下切勿连接电源，这样可能会对振荡器造成损坏。

Due to the different capacity of the cleaning tank of the ultrasonic oscillator, the requirements for the liquid level are also different. Before using the ultrasonic oscillator, carefully read the instructions, understand the low tank depth and the liquid level depth in detail, and do not connect the power supply when the liquid level is not up to the standard or there is no liquid, which may cause damage to the oscillator.

二注意清洗剂种类（勿选择腐蚀类产品）

II. Pay attention to the type of cleaning agent (do not choose corrosive products)

超声波振荡器可以使用纯水等进行清洗，同时也可以使用水加清洗剂进行清洁效果更佳，针对不同的工件而言，清洗剂的选择要尤为注意。首先清洗剂不可以对振荡器本体造成腐蚀或损害，同时也要满足工件的清洗要求，要注意温度对于清洗剂的性状改变情况，一些清洗剂耐温性较差，经高温后可能会腐蚀振荡器，所以要避免使用此类清洗材料。

The ultrasonic oscillator can be cleaned with pure water, etc. At the same time, it can also be cleaned with water and detergent. For different workpieces, the selection of detergent should be paid special attention. First of all, the cleaning agent can not cause corrosion or damage to the oscillator body, but also meet the cleaning requirements of the workpiece. Pay attention to the change of the properties of the cleaning agent due to the temperature. Some cleaning agents have poor temperature resistance and may corrode the oscillator after high temperature, so avoid using such cleaning materials.

三注意温度峰值（峰值时禁止人工开机）

III. Pay attention to the peak temperature (it is forbidden to start the machine manually at the peak)

绝大部分高品质的超声波振荡器都设有自我保护功能，这样可以保护设备自身安全，当使用较长时间后振荡器内部温度便会成倍增长，此时设备自动探温系统便会发出信号，使设备立即停机，处于休眠状态。此时禁止人工开机，以免排热不畅导致设备的永久性损坏。

Most high-quality ultrasonic oscillators are equipped with self-protection function, which can protect the safety of the equipment. When used for a long time, the internal temperature of the oscillator will multiply. At this time, the automatic temperature detection system of the equipment will send a signal to stop the equipment immediately and put it in sleep. At this time, it is forbidden to start the machine manually to avoid permanent damage to the equipment due to poor heat removal.

四注意内槽清洁（防止影响下批工件）

IV. Pay attention to the cleaning of the inner groove (prevent affecting the next batch of workpieces)

一般来说的超声波振荡器工作频率不宜太过频繁，间歇式工作，要注意将内槽进行清洁，避免工件中的污垢腐蚀内胆，同时也避免清洗剂对于其它工件产生影响。所以从原则上来说，不同类型的工件使用不同的超声波振荡器清洗剂后，要将内槽内液排出后进行清洗，再清洗下一波工件。

Generally speaking, the working frequency of professional ultrasonic oscillator should not be too frequent. For intermittent operation, pay attention to cleaning the inner groove to prevent the dirt in the workpiece from corroding the inner liner, and also avoid the impact of cleaning agent on other workpieces. Therefore, in principle, after using different ultrasonic oscillator cleaning agents for different types of workpieces, the liquid in the inner tank should be discharged and cleaned before cleaning the next wave of workpieces.

同时还要注意振荡器使用完成后要及时的关闭开关，并且将电源拔下，将电源长期停留于排线孔中也会加速其老化，而且可能还会引发危险。同时要注意将超声波振荡器冲洗完成后，好可以使用吸水布将水分清除，这样可以延长振荡器的使用寿命。更多相关使用就来咨询我们http://senfuai.com吧！

At the same time, pay attention to timely turn off the switch after the oscillator is used, and unplug the power supply. If the power supply stays in the cable hole for a long time, it will also accelerate its aging, and may cause danger. At the same time, it should be noted that after the ultrasonic oscillator is washed, the water can be removed with absorbent cloth, which can prolong the service life of the oscillator. Consult us for more information http://senfuai.com Come on!