CNC高压清洗机设备在我们的生活和工业生产中都发挥着十分重要的作用，不少清洁公司和工厂都会使用到这类设备，很多人在使用设备的时候遇到压力不足、喷头不出水等问题不知道该如何解决。下面小编就为大家介绍一下CNC高压清洗机常见问题的解决方法。

CNC high-pressure cleaning machine equipment plays a very important role in our life and industrial production. Many cleaning companies and factories will use this kind of equipment. Many people do not know how to solve the problems such as insufficient pressure and no water from the nozzle when using the equipment. Now, Yangzi Xiaobian will introduce solutions to common problems of CNC high-pressure washer.

1、CNC高压清洗机压力不稳定：

1. The pressure of CNC high-pressure washer is unstable:

设备出现压力不稳定的情况一般是因为高压水泵或者进水管路中吸入了空气所导致的，需要我们检查水源的压力是否足够，进水过滤器是否堵塞，当发现过滤网堵塞时，及时的进行清洗，晾干以后使用就可以了。

The unstable pressure of the equipment is generally caused by the intake of air from the high-pressure water pump or the water inlet pipe. We need to check whether the pressure of the water source is sufficient and whether the water inlet filter is blocked. If the filter screen is blocked, clean it in time and dry it before use.

2、运行过程中出现异响：

2. Abnormal noise during operation:

设备出现异响一般是由于电机轴承缺油所导致的，遇到这类问题时在电机的注油孔注入普通黄油就可以了，一般这种情况发生的不多，我们在日常使用过程中做好定期的维护和检查就可以了。

The abnormal noise of the equipment is generally caused by the lack of oil in the motor bearing. In case of such problems, it is OK to inject ordinary grease into the oil injection hole of the motor. Generally, this kind of situation does not occur much. We can do regular maintenance and inspection in the daily use process.

3、使用后设备压力降低：

3. The pressure of the equipment decreases after use:

遇到这个问题我们首先要检查高压喷嘴是否出现严重磨损的情况，普通压力的CNC高压清洗机喷嘴基本不会出现磨损的情况，但是一些超CNC高压清洗机设备在运行过程中会进行过热处理，比较容易出现磨损的情况。遇到这类情况要注意检查调压阀和水泵内部的密封组件。

When encountering this problem, we should first check whether the high-pressure nozzle is seriously worn. The nozzle of the ordinary pressure CNC high-pressure washer will not be worn, but some super CNC high-pressure washer equipment will be overheated during operation, which is more prone to wear. In such cases, pay attention to check the pressure regulating valve and the sealing components inside the water pump.

4、高压水枪不出水：

4. No water from high-pressure water gun:

当调压阀压力正常而高压水枪却不出水，或者是喷嘴喷射的水流不规则、分散的时候，说明高压水枪内出现了异物堵塞的情况，要及时的清理喷嘴。

When the pressure of the pressure regulating valve is normal but the high-pressure water gun does not discharge water, or the water jet from the nozzle is irregular and dispersed, it indicates that there is a blockage of foreign matters in the high-pressure water gun, and the nozzle should be cleaned in time.

5、水泵底部漏油：

5. Oil leakage at the bottom of water pump:

CNC高压清洗机水泵底部漏油主要是由于泵内油封损坏，遇到这类情况我们要及时的更换油封；当水泵在运转过程中，曲轴和连轴不停的做往返运动，这时主要靠油给设备进行润滑和降温，所以水泵在使用过程中不能缺少润滑油。

The oil leakage at the bottom of the water pump of the CNC high-pressure washer is mainly due to the damage of the oil seal in the pump. In this case, we should replace the oil seal in time; When the water pump is running, the crankshaft and coupling keep moving back and forth. At this time, oil is mainly used to lubricate and cool the equipment, so the water pump cannot be short of lubricating oil during use.

以上这些问题我们在使用过程中很可能会遇到，其实只要在使用CNC高压清洗机的过程中做好维护和保养工作，就能在一定程度上避免许多问题，特别是由于配件问题导致的故障。更多相关使用问题或者购买问题就来我们网站senfuai.com咨询了解吧！

We are likely to encounter the above problems in the process of use. In fact, as long as we do a good job of maintenance and servicing in the process of using the CNC high-pressure washer, we can avoid many problems to a certain extent, especially those caused by parts problems. For more questions about use or purchase, please visit our website senfuai.com!