碳氢清洗机买了碳氢清洗机后，使用一段时间后，细心的朋友可能会发现他们的碳氢清洗机的功率一天比一天低。情况如何？面对这样的情况，您别担心，来看看小编分析的原因您就知道怎么做了。

After buying a hydrocarbon washer, careful friends may find that the power of their hydrocarbon washer is getting lower day by day after using it for a period of time. How is it going? In the face of such a situation, don't worry. Look at the reasons of the minor editor's analysis and you will know how to do it.

碳氢清洗机主要原因是机械设备使用时间过长，变频调速器逐渐老化，特性降低。维护方法可以选择提高超声波输出功率，但这种维护方法可以治疗症状而不是根本原因，容易增加换能器的热量，从而损坏机器。

The main reasons for hydrocarbon cleaning machine are that the mechanical equipment has been used for a long time, the frequency converter is gradually aging, and the characteristics are reduced. The maintenance method can choose to increase the ultrasonic output power, but this maintenance method can treat the symptoms rather than the root cause, which is easy to increase the heat of the transducer, thus damaging the machine.

碳氢清洗机碳氢清洗机的换能器吸湿，绝缘电阻正常或部分损坏。在这种情况下，好的选择是拆卸和更换损坏的传感器。其他原因，电缆是外部损坏还是吸湿，电源电压过低。

The transducer of the hydrocarbon washer absorbs moisture and the insulation resistance is normal or partially damaged. In this case, a good choice is to remove and replace the damaged sensor. For other reasons, the cable is externally damaged or hygroscopic, and the power supply voltage is too low.

传感器没有剥落，在脱胶状态下，碳氢清洗机的底部不受振动吸收材料或工件的干扰。环中的电源可以移动其工作点并重新调整工作点。超声波清洗设备的输出功率较小。更换或修改电源，以增加传感器的数量。

The sensor does not peel off. Under the degumming state, the bottom of the hydrocarbon washer is not interfered by vibration absorbing materials or workpieces. The power supply in the ring can move its work point and readjust it. The output power of ultrasonic cleaning equipment is small. Replace or modify the power supply to increase the number of sensors.

碳氢清洗机其他未知超声功率减弱，如放置清洁材料，如，清除和更换清洁剂等。在上述情况下，更有可能损坏超声波清洗设备的换能器。

Other unknown ultrasonic power of hydrocarbon cleaning machine is weakened, such as placing cleaning materials, such as removing and replacing cleaning agent. Under the above circumstances, it is more likely to damage the transducer of the ultrasonic cleaning equipment.

如果输出功率低或弱，请先检查传感器是否有问题。如果无法判断原因，应停止使用碳氢清洗机，不要再次使用。但是，随着输出功率的降低，可以在有时间的时候将其送回维修。

If the output power is low or weak, check the sensor first. If the cause cannot be determined, stop using the hydrocarbon washer and do not use it again. However, as the output power decreases, it can be sent back for maintenance when there is time.

当然针对维修，您可以先查询下自己购买产品的厂家怎么样，售后的服务能不能及时跟上。更多相关内容就来我们网站senfuai.com咨询吧！

Of course, for maintenance, you can first inquire about the manufacturer who bought the product and whether the after-sales service can keep up. For more information, please visit our website senfuai.com!